How To Install Shower Pan In Basement
How to Install a Fiberglass Base Over Concrete
Updated: Dec. 03, 2022
Plumb the drain using a special leak-proof drain associates
Install a fiberglass shower stall over a concrete floor using a special bleed associates that eliminates leaks. You run the drain line under the concrete.
You might besides like: TBD
Stride 1. Shower Drain Installation: Run a drainpipe under the concrete floor
Shower stall on physical
A shower usually requires a two-in. bleed, with the P-trap located under the concrete slab.
If you want to install a shower over a concrete floor, a fiberglass shower stall volition piece of work just fine. Ideally, you'll already accept a drain roughed in, with the pipage sticking a few inches higher up the floor. Otherwise you have to break through the concrete to run a new line for a shower stall installation.
If you take a pipe stubbed up, call the plumber or contractor who did the work to confirm it. The 2-in. pipe is typically the shower or tub drain. Line it upwardly exactly with the drain hole in the bottom of your shower bay. This position determines the location of the stud walls around the shower. The supplier may be able to provide a dimensioned drawing of the shower bay, and so you don't actually accept to put information technology in first.
If the existing 2-in. drainpipe isn't where you lot want it, you'll have to pause up the physical and replumb the drain.
Brand sure the drainpipe extends at to the lowest degree an inch above the concrete. If the pipe is besides brusk, you'll have to break up the concrete and extend information technology. Also, you'll need at least a 1-ane/ii-in. space between the pipe and the concrete to suit the bleed associates (come across photo below). If there isn't, advisedly chisel out the concrete around the pipe.
Tip: If you're considering a unmarried-piece shower bay, make sure you can get it into the new bathroom space. You lot may accept to bring the unit of measurement into the space before framing the doorway or walls. If admission is a problem, cheque out multiple-piece units that will fit through doorways more than easily.
Pace ii. Shower Bleed Installation: Mount the leakproof drain assembly
Drain assembly close-up
The assembly locks tightly to the pipe and clamps to the edge of the shower base to make leakproof seals.
After you frame the shower walls to fit the shower bay, lay the bay on its back and install the shower drain. Use a special leakproof shower drain assembly called the No-Caulk Shower Drain. It's available at abode centers and plumbing supply houses. Although these bleed baskets are available in plastic, I'd opt for the brass 1. Follow these steps to attach the shower to the bleed:
- Whorl out a ringlet (about the diameter of a pencil) of plumber's putty (available at all hardware stores) and wrap it under the drain basket flange.
- Hold the shower bleed handbasket in position in the shower bay bleed hole, slide on the washers, and and then thread on and hand-tighten the outside setting ring. Tighten the ring with a large sideslip-joint pliers until it'due south firmly in identify. You shouldn't be able to move the shower basket by paw. The plumber's putty volition squeeze out.
- Lower the shower bay and basket assembly over the drainpipe. Mark the pipe almost 3/4 in. below the drain basket flange.
- Lift the shower bay out of the mode and cut the drainpipe to length. A hacksaw works well. Make sure to cut the piping square, not angled.
- Ready the shower bay and basket associates back over the pipe. Slide the caulking gasket over the pipe and push it all the way downwards then information technology sits against the lip at the bottom of the drain basket. Yous may accept to tap this gasket into identify with a hammer and a thin piece of wood.
- Thread on the caulking nut and firmly tighten to compress the caulking gasket and seal the pipage. Utilise the slotted bar tool that comes with the drain assembly. Stick the flat bract of a screwdriver into the bar'south slot and firmly mitt-tighten.
- Snap on the perforated drain encompass (not shown).
Required Tools for this Project
Take the necessary tools for this DIY shower drain installation project lined upwardly before you start—you'll save time and frustration.
Apartment-blade screwdriver
Required Materials for this Project
Avoid terminal-infinitesimal shopping trips by having all your materials ready ahead of fourth dimension for a shower stall installation. Here's a list.
Originally Published: Dec 03, 2022
Source: https://www.familyhandyman.com/project/how-to-install-a-fiberglass-base-over-concrete/
Posted by: aguilarpreve1968.blogspot.com
0 Response to "How To Install Shower Pan In Basement"
Post a Comment